Cross Technologies 2416-x02 Manual de Instruções

Instruction Manual Model 2416-x02Multi Channel Downconverter2416-402 Four Channel • 2416-302 Three Channel • 2416-202 Two Channel •

(C) Commands Table 1.2 lists the commands for the 2416-x02 and briefly describes them. After a command is sent the 2416-x02 sends a return “>” ind

1.5 Environmental Use InformationA. Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions located in the u

2.0 Installation2.1 MechanicalThe 2416-x02 consists of one RF/Controller PCB housed in a 1 RU (1 3/4 inch high) by 16 inch deep chassis. A switchin

2.2 Rear Panel Input/Output Signals Figure 2.2 shows the input and output connectors on the rear panel. PSA & PSB - POWER INAC inpu

2.3 Front Panel Controls and Indicators - The following are the front panel controls and indicators.MENUEXECUTE1674.125 1926.250REMOTE POWERLCD FR

2.4 Operation2.4.1 Installing and Operating the 2416-x02 Downconverter1. Connect a -50 dBm to -20 dBm signal to RF IN, J2 (Figure 2.2).2. Connect t

2.5 Power On SettingsFigure 2.5 shows the various Front Panel LCD Displays that you will see during the Power Up sequence and the Settings modes. Th

2.5.2 Frequency ChangesAt any time during the modification process, if you have made a mistake and do not wish to save the changes you have made, do

2.6 Menu SettingsAll program changes must start with the operation of the Menu/Execute switch and must also end with the operation of the Menu/Execut

3.0 Ethernet Interface Installation and Operation (Option W8, W18 or W28)This manual applies to Cross Technologies products equipped with a 10/100 Ba

INSTRUCTION MANUALModel 2416-x02 Multi Channel DownconverterTABLE OF CONTENTS PAGEWarranty 21.0 General 31.1 Equipment Description 31.2 Technica

Figure 3.1: Configuration Manager Screen(Example above shows Configuration Manger Screen for Model 2416-402) Once logged in, you will be presented

Figure 3.2: Network Settings Web Page Screen(Example above shows Network Settings Screen for Model 2416-402)2416-402 Manual, Rev. D

3.3 Web Page M & CEnter the following address in a web browser to access the M&C web page:http://<ip address>/serial/0/setup.htm where

3.4 SNMP ConfigurationSetting of SNMP parameters such as Community Write and Community Read strings requires a Telnet® connection to port 9999. The f

If you select Public, access is allowed for any number of authorized IP addresses of SNMP Managers. It is not required to enter IP Addresses of SNMP

CROSS TECHNOLOGIES, INC.6170 Shiloh RoadAlpharetta, Georgia 30005(770) 886-8005FAX (770) 886-7964Toll Free 888-900-5588WEB www.crosstechnologies.com E

Model 2416-x02 Multi Channel Downconverter2416-402 Four Channel • 2416-302 Three Channel • 2416-202 Two Channel • 2416-102 One Channel1.0 Gener

1.2 Technical Specificaions <-60 dB typical, <-50 dB min.; G = 30, -30 dBm input level Channel to Channel isolation -50 to -20 dBm Input

(Technical Specifications continued from page 4...) 140 ±36/70 ±18 MHz Selectable W140/70-x Ethernet with Web Browser W8 - Redundant Power Suppl

1.3 Engineering Application (Note 1): Fractional PLL (Phase Lock Loop) ImplementationThe purpose of this Engineering Application Note is to inform ou

1.4 Monitor and Control InterfaceA) Remote serial interfaceProtocol: RS-232C, 9600 baud rate, no parity, 8 data bits, 1 start bit, and 1 stop bit

B) Status Requests Table 1.1 lists the status requests for the 2416-x02 and briefly describes them.* PPLEASE NOTE: Status requests of values specific

(Status Request continued from page 7...)TABLE 1.1 2416-x02 Statuus Status Requests Coontinued TABLE 1.1 2416-x02 Status Requests Contin